top of page

WHEEL COMPONENTS

The Rybro® range of wheel components assist in fitting a wheel to a castor or trolley. We also supply bushes for the manufacture of solid rubber or split rim rubber wheels

PILOT BORE BUSH SET

Pilot-bore-bush
  • Glass filled nylon bush set, used to replace bearings, creating a pilot bore wheel.

  • Can be used to replace a bearing with a 47mm OD

  • Minimum Hub width 50mm

  • Minimum Bearing Seat Depth - 15mm

4" PNEUMATIC RIM SET

4x210 Split Rim-20_edited.png
  • Wheel rim 2.10-4 for transport carts, material handling, wheelbarrows and trolleys.

  • Manufactured from Impact resistant Polypropylene.

  • This rim can be fitted with tyre size (not included):

    • 3.00-4

    • 4.00-4

    • 260x85

    • 4.10/3.50-4

    • 9x3.50-4

    • 11x4.00-4

Technical details

  • Assembled divided rim

  • Max Inflation Rating - 2.5BAR/36PSI

  • 6x M6x40 Cap Screws and Nyloc Nuts included

  • Rim width: 2.10 inch (53mm)

  • Hub length - 80mm

  • Diameter rim: 4 inch (100mm)

  • Offset: Neutral / No offset

  • Bearing in hub: 6905 - 25mm ID or 6004 - 20mm ID

  • Colour: Black

8" PNEUMATIC RIM SET

8inch pneumatic rim.png
  • Wheel rim 2.50-8 for transport carts, material handling, wheelbarrows and trolleys.

  • Manufactured from Impact resistant Polypropylene.

  • This rim can be fitted with tyre size (not included):

    • 3.00-8

    • 3.50-8

    • 4.00-8

    • 4.10/3.50-8

    • 4.80/3.50-8

Technical details

  • Assembled divided rim

  • Max Inflation Rating - 2.5BAR/36PSI

  • 6x M8x40 Hex Set Screws, washers and Nyloc Nuts included

  • Rim width: 2.50 inch (63.50mm)

  • Hub length - 80mm

  • Diameter rim: 8 inch (200mm)

  • Offset: Neutral / No offset

  • Bearing in hub: 6005 - 25mm ID or 6204 - 20mm ID

  • Plain Bore Bushes in place of bearings are available.

  • Colour: Black

AXLE BUSHES

polybush-wheelbarrow.jpg
  • Polyprop bushes are used inside split rim rubber wheels.

  • This is a wear component and should be replaced periodically to prevent damage to the rim.

  • THIS RANGE IS SPECIAL ORDER ONLY - MOQS APPLY

MOLD-IN AXLE BUSH FOR RUBBER WHEELS

rubber-wheel-axle-bush.jpg
  • Designed for Solid Rubber compression moulded wheels (Wheel Barrow, Jockey & Trolley Tyres)

  • Designed to withstand moulding pressure and heat (resistant up to 220C).

  • Tooth formation aids in a strong bond with rubber wheel.

  • Please request samples prior to manufacturing your rubber moulds.

  • These bushes will shrink during rubber moulding process.

  • Sizes stated are the suggested finished sizes of your product, but may vary due to your moulds.

SPLIT RIM SET

wheel-split-rim.png
split_centre_2_edited.png
  • Light weight replacement for steel split centres

  • No additional bush required

  • Compatible with both 150mm & 200mm Rubber Tyres.

  • Sold in pairs

  • Available in Black or White

BOLTS, NUTS AND REDUCING SLEEVES

  • Available for all wheels from 75mm in diameter.

  • Sleeves are available to reduce bore ID down to a specific bolt size

  • Sleeves are supplied in raw mild steel or Glass Filled Nylon

  • Steel Sleeves can be ordered in custom lengths

  • M8, M10 and M12 Galvanised bolts and Nyloc nuts also available

BOLTSET.png

WASHERS AND SPACERS

  • Manufactured from Polyprop

  • Used in the assembly of trolleys and castors

trolley-washer.jpg
WhatsApp.svg.png
bottom of page